Who's Online
2 registered (Abeygunz, quietman), 6 Guests and 8 Spiders online.
Key: Admin, Global Mod, Mod
Topic Options
#1471537 - 03/17/19 10:17 AM 10.5 build
Bcmgunfighter Offline
Professional VGT lurker

Registered: 12/20/12
Posts: 1455
Loc: Virginia
City or County: Rochelle
I have a question that Im hoping a fellow member can shed some light on. Ive been building a couple of ARs for the last few years now. Ive been collecting used parts when possible, and attempting to acquire the hardest to find parts first. Both builds are almost done, and while Im not currently a stamp collector, Ive been building these to suppress them in the (hopefully) near future. That brings me to the pickle that Im in... I went with a Noveske CQB barrel (10.5) and the almost impossible to find, DD Lite 10 II rail. There was/is absolutely no info on this combo anywhere that Ive been able to find, so I didnt know that the rail will most likely keep me from suppressing. Im planning on putting a Lantac Dragon ASR on, but even with a few shims, there is very little chance that it will work.
Do any of you know of either a suppressor that is thin enough, or a mount that with keep the suppressor far enough away from the rail?
If I knew someone who owns an ASR, I would just go ahead and buy the mount to see if buy chance it works... worst case scenario, the Dragon ASR goes on a 16 lol





UPDATE...

It looks like Ill be using the 10.5 for another build with an NSR 9, so now I just have to find a sub $450 12.5 Crusader to get cut down to 11.5 facepalm ...since Noveske only makes a stainless 11.5.


Edited by Bcmgunfighter (04/14/19 05:37 PM)
_________________________
Virginia Gun Trader's Noveske hoarder

Always looking for
Noveske VIS uppers
Noveske MUR uppers
Noveske SWS rails
Noveske Gen II lowers
Daniel Defense Omega X 7.0
Daniel Defense Lite Rail II 10
Winchester Model 72a bolt

MY DO NOT DEAL LIST...

BearsFan5

Top
#1481951 - 04/14/19 05:30 PM Re: 10.5 build [Re: Bcmgunfighter]
Bcmgunfighter Offline
Professional VGT lurker

Registered: 12/20/12
Posts: 1455
Loc: Virginia
City or County: Rochelle
So Ive been looking at info on suppressing 10.5 5.56 ARs. One guy claims that he blew out a suppressor at that length... another guy claims that suppressors will wear out much faster, and goes on to say that 12.5 seems to be the sweet spot?
Im pretty set on keeping the 10.5, but not at the cost of a can. I would assume that the SiCo suppressors are good to go at 10.5?
_________________________
Virginia Gun Trader's Noveske hoarder

Always looking for
Noveske VIS uppers
Noveske MUR uppers
Noveske SWS rails
Noveske Gen II lowers
Daniel Defense Omega X 7.0
Daniel Defense Lite Rail II 10
Winchester Model 72a bolt

MY DO NOT DEAL LIST...

BearsFan5

Top
#1482132 - 04/15/19 09:22 AM Re: 10.5 build [Re: Bcmgunfighter]
JustOneMore754 Offline
Bolt action

Registered: 12/27/17
Posts: 142
Loc: Merrifield
City or County: Fairfax
I have a SiCo Omega 300 that I use on my 10.5 pistol and it performs just fine however I dont torture test it. I believe the issue most people see with suppressing shorter barrels is from increased heat (since the powder is still burning when it hits the suppressor). So cans that are made of less durable materials (like plain steel) would deform faster. I know SiCo is pitching their new chimera 300 can as full-auto rated & safe for any barrel length but in both cases the issue is heat build up. Im 99% sure the omega I have is also full auto rated so I you should be fine as long as youre not doing endless mag dumps out of your sbr you wont break it. Plus side if you do somehow break it SiCos customer service is top notch and theyll fix your can.
_________________________
Prefer transactions to take place within an hours drive of Fairfax.

I can always be tempted by:
- SPAS-12 with a folding stock.
- Shooter grade Luger
- Schofield reproduction
- S&W 586 with a 4 barrel
- Almost any gun under $300

Top
#1493934 - 05/19/19 09:24 AM Re: 10.5 build [Re: JustOneMore754]
Bcmgunfighter Offline
Professional VGT lurker

Registered: 12/20/12
Posts: 1455
Loc: Virginia
City or County: Rochelle
Originally Posted By: JustOneMore754
I have a SiCo Omega 300 that I use on my 10.5 pistol and it performs just fine however I dont torture test it. I believe the issue most people see with suppressing shorter barrels is from increased heat (since the powder is still burning when it hits the suppressor). So cans that are made of less durable materials (like plain steel) would deform faster. I know SiCo is pitching their new chimera 300 can as full-auto rated & safe for any barrel length but in both cases the issue is heat build up. Im 99% sure the omega I have is also full auto rated so I you should be fine as long as youre not doing endless mag dumps out of your sbr you wont break it. Plus side if you do somehow break it SiCos customer service is top notch and theyll fix your can.

Thanks for the info! My Lantac E-BCGs for both builds just arrived (ordered in January from Midway), so Im hoping to get the suppressor show on the road soon. I decided that Ill just keep my eyes open for a DD Lite Rail 9 II to swap out with my 10 II when Im ready to suppress the 10.5 build.
_________________________
Virginia Gun Trader's Noveske hoarder

Always looking for
Noveske VIS uppers
Noveske MUR uppers
Noveske SWS rails
Noveske Gen II lowers
Daniel Defense Omega X 7.0
Daniel Defense Lite Rail II 10
Winchester Model 72a bolt

MY DO NOT DEAL LIST...

BearsFan5

Top
#1510277 - 07/04/19 05:36 PM Re: 10.5 build [Re: Bcmgunfighter]
Execprotect Offline
Dialed In

Registered: 06/22/14
Posts: 1674
Loc: Fauquier-Catlett
City or County: Fauquier
Try to get an AAC M4-2000. They are built like a tank and AAC rates them down to 10.5" barrels.

Top
#1515297 - 07/17/19 07:40 PM Re: 10.5 build [Re: Execprotect]
Pog926 Offline
Marksman

Registered: 07/07/10
Posts: 239
Loc: Fredericksburg
City or County: Fredericksburg
I have a couple of 10.5 builds and a 11.5 build. I have a SiCo Saker 7.62 and Hybrid. No issues on clearance of the rail with a Centurion C4 cutout.

Top
#1516728 - 07/21/19 02:43 PM Re: 10.5 build [Re: Bcmgunfighter]
Bcmgunfighter Offline
Professional VGT lurker

Registered: 12/20/12
Posts: 1455
Loc: Virginia
City or County: Rochelle
Thanks for the info, guys!

I FINALLY had a chance to shoot the 10.5 a couple of days ago. Its as smooth as can be, and I love everything in regards to the build, but every time I pulled the trigger, it was like someone was smacking me in the face with a memory foam pillow. To be honest, it was a little more than I was expecting, especially considering that my 13.7 feels softer and smoother shooting than my 16 ARs.

I found a nice little info chart on the Silencershop website.
It looks like I should pull the trigger on a Saker 762 ASR. Im not sure how the smaller Saker 556 is better rated across the board, but for what I have, I should be fine with the 762.
_________________________
Virginia Gun Trader's Noveske hoarder

Always looking for
Noveske VIS uppers
Noveske MUR uppers
Noveske SWS rails
Noveske Gen II lowers
Daniel Defense Omega X 7.0
Daniel Defense Lite Rail II 10
Winchester Model 72a bolt

MY DO NOT DEAL LIST...

BearsFan5

Top