|
#1935488 - 10/01/22 04:54 PM
Need an obstruction removed.
|
TheReluctantPrep
Pea shooter
Registered: 12/30/19
Posts: 5
Loc: VA
City or County: Suffolk
|
So, I have a rifle with an obstruction....
Apparently, a bamboo dowel was used to try and clean a rifle I own. Anyway, the fact the dowel was shorter than barrel was not considered when this make shift rod was used. Resulting in patch and dowel being firmly stuck inside the barrel.
When came back to me, I tried tapping it out with a cleaning rod....but its good and jammed and I dont want to damaged the rifle.
I need a Gunsmith that can remove obstruction. I have emailed four different gunsmiths and gotten no response or....one that said, I dont know when I could get to it.
Can someone point me to a good gun smith that will actually be interested in helping me.
Close to Va Beach would be a plus, but at this point I will travel a good distance.
_________________________
Come and Take
|
Top
|
|
|
#1940392 - 10/15/22 06:16 PM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
Domonicm
Gun fool
Registered: 01/02/10
Posts: 1139
Loc: Alexandria NOVA
City or County: Alexandria
|
Watch a few of these videos https://youtu.be/0APH-XNu55IIf it’s just a patch you can try to dissolve it which will loosen the fibers and you can tap it out. Need to let it soak for a while Lucky you just have fiber patch and wood which you can degrade Next time use a snake wire pull
_________________________
"Gun Control means using both hands"
|
Top
|
|
|
#1942065 - 10/21/22 09:12 AM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
Bcmgunfighter
Not all ARs are created equal...
Registered: 12/20/12
Posts: 3386
Loc: Virginia
City or County: Rochelle
|
Fortunately, as hard as bamboo can be, it certainly won’t damage steel. How much of the barrel does the bamboo take up? (Width, not length)
_________________________
Noveske 13.7” barrels VIS uppers Gen II lowers DD Lite Rail II 14
MY DO NOT DEAL LIST smilewhenIshoot - “There is zero evidence of voter fraud” Manwich23 - supports Chinese/US power grid JiveBunny Downhillshot Alwaystrading dcarms - ATF CUCK
|
Top
|
|
|
#1952181 - 11/21/22 11:42 AM
Re: Need an obstruction removed.
[Re: Bcmgunfighter]
|
TheReluctantPrep
Pea shooter
Registered: 12/30/19
Posts: 5
Loc: VA
City or County: Suffolk
|
Apparently the bamboo is most of the with, but a patch causing it to be stuck.
_________________________
Come and Take
|
Top
|
|
|
#1952448 - 11/22/22 12:25 AM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
Bcmgunfighter
Not all ARs are created equal...
Registered: 12/20/12
Posts: 3386
Loc: Virginia
City or County: Rochelle
|
Personally, I would take an oak dowel that is very close in size to whatever caliber the weapon is… tap it through AGAINST THE PATCH.
_________________________
Noveske 13.7” barrels VIS uppers Gen II lowers DD Lite Rail II 14
MY DO NOT DEAL LIST smilewhenIshoot - “There is zero evidence of voter fraud” Manwich23 - supports Chinese/US power grid JiveBunny Downhillshot Alwaystrading dcarms - ATF CUCK
|
Top
|
|
|
#1955423 - 11/30/22 05:14 PM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
TheReluctantPrep
Pea shooter
Registered: 12/30/19
Posts: 5
Loc: VA
City or County: Suffolk
|
Yea, I am going to try. I hope that works. Not sure my next plan...
_________________________
Come and Take
|
Top
|
|
|
#1957636 - 12/06/22 10:06 PM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
num1fordfan
RUGERS and T.B.T.B.E.B
Registered: 09/03/09
Posts: 10145
Loc: prince george , va 23875
City or County: PRINCE GEORGE
|
What type of gun is it , what caliber?
_________________________
IMA TURKEY SHOOTIN FOOL. INTEREST IS UP AND THE STOCK MARKETS DOWN YA GONNA GET MUGGED IF YA GO DOWN TOWN
|
Top
|
|
|
#1959340 - 12/11/22 09:34 PM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
TheReluctantPrep
Pea shooter
Registered: 12/30/19
Posts: 5
Loc: VA
City or County: Suffolk
|
It is a 30-06 Remington 700 I got some advise offline as well and was able to remove the obstruction. This is what I did. I used a flashlight and figured out the patch side of the obstruction. It was on the breach side. I put the rifle in a rifle vice with the muzzle adjusted down. I then added about twenty drops of Kroil oil down the breach side of the rifle barrel and waited. Then I bought a couple dowels, wood, oak. 1/4 turned out to be the right size. It was almost the size of the barrel but still had a little space for perhaps letting the patch stay while obstruction moved. Then used the dowel and a hammer. After about 50 measured......hard taps I was very frustrated that nothing was happening. But, I thought to mark the dowel to see if it was moving....tapped about a dozen more times and saw it was moving very slowly. About two dozen more firm taps and it was freed! I cleaned the Rifle and then looked a the rifling of the barrel and it looks factory perfect. I could not be happier.
Thanks to Bcmgunfighter and my friend offline for the great advice.
_________________________
Come and Take
|
Top
|
|
|
#1959342 - 12/11/22 09:35 PM
Re: Need an obstruction removed.
[Re: Bcmgunfighter]
|
TheReluctantPrep
Pea shooter
Registered: 12/30/19
Posts: 5
Loc: VA
City or County: Suffolk
|
Bcmgunfighter
Thank You Brother
Edited by TheReluctantPrep (12/11/22 09:36 PM) Edit Reason: Though was going to reply to a message above not at the end. Changed to reflect where in the thread it showed up and to make sense.
_________________________
Come and Take
|
Top
|
|
|
#1960607 - 12/15/22 07:00 PM
Re: Need an obstruction removed.
[Re: TheReluctantPrep]
|
Bcmgunfighter
Not all ARs are created equal...
Registered: 12/20/12
Posts: 3386
Loc: Virginia
City or County: Rochelle
|
Well that is phenomenal news! Happy to help, brother! Fun fact... bamboo is MUCH harder than oak. In this case though, with the bamboo being so thin, and of course hollow, the oak dowel wins. I still can’t believe that someone thought that it was a good idea to try to use that thin cane as a cleaning rod ![shocked shocked](https://vaguntrader.com/forums/images/graemlins/default/shocked.gif)
_________________________
Noveske 13.7” barrels VIS uppers Gen II lowers DD Lite Rail II 14
MY DO NOT DEAL LIST smilewhenIshoot - “There is zero evidence of voter fraud” Manwich23 - supports Chinese/US power grid JiveBunny Downhillshot Alwaystrading dcarms - ATF CUCK
|
Top
|
|
|
|